Type: Driver
File Name:
File Size: 40.7 MB
18 (4.07)
Downloads: 10
Supported systems: Windows Vista (32/64-bit), Windows XP (32/64-bit), Windows 8, Windows 10
Price: Free* (*Free Registration Required)

Download Now

See How to mi drivers and software from the Epson xx for more. Xx the efficiency of the Epson M with more pas on a voyage through Amigo mi. Pull the proof spring A item 75 out of the spring case B in the direction shown in the picture below using flat nose pliers until it slips out of the case. When lipi t2250 reassemble the proof spring, it is recommended to use a new spring which is part of a new spare part set, in order to improve the function of the automatically paperpath selection. The spare part set contains two proof springs, two screws and four disks.

Place two disks on each screw and then fix the proof spring item 75 inside the spring lipi t2250 case. The necessary holes are provided and must not be drilled. Place the empty left side plate so that the outside faces down and the bottom edge towards you. Insert the toothed wheel A item 96 positioned under the push bar. Position the gear shaft rear E item 81 in the location provided in the side plate in such a way that the ring with the pins points toward you and the curve of the semidisc points to the right. In addition, the straight side of the semidisc must be at an angle of 90 degrees to the side plate. The gear shaft rear is not fastened.

Tally Dot Matrix T - printer - monochrome - dot-matrix Specs - CNET

Mount the toothed wheel 1 item 76 and 2 item Ensure that the position of the gear shaft E remains unchanged. Insert the push bar D item 70 vertically in such a way that the recess 1 on the push bar engages with the guide provided in the side plate 2. For this purpose, the mark for position 1 lipi t2250 also pageupper drawing must be at about 3 mm to the left of the mark on the side plate. Take care not to move or turn the gear shaft rear E. Then slide the push bar into position 1. Insert the gear shaft front F in such a way that the ring with the pins points away from you and the semidisc towards you. The curve of the semidisc must point to the right, the straight side to the left at an angle of 90 to the side plate.


The gear shaft front is not fastened, either. Press the gear shaft front F down and slide lipi t2250 push bar D into position 6.

This will fasten the gear shaft rear E and the gear shaft front F. Make sure that the straight sides of the semidiscs of lipi t2250 shafts point to the same direction and continue to be at an angle of 90 to the side plate. Spare parts and schematics The spare parts lists show: 1. The position of the part in the explosion drawing item.

The name of the part. The classification of parts. Name Casing, upper Casing below Upper cover rear incl. Paper guide tractor 1 Panel cpl. Carriage cpl. Guide wheel toothed belt Carriage shaft cpl. Lipi t2250 connection plate Ribbon drive with belt cpl. ESD spring printing bar Printing bar cpl. Carriage shaft front Flap mounted upper lipi t2250 cpl.

Driving shaft cpl. BG lower friction cpl. Part no. T narrow lipi t2250 part of item 29 T narrow printer Part no.

Tally Dot Matrix Printers Models T2150 and T2250

Name Panel cpl. Sensor Lipi t2250 cpl.Tally Dot Matrix Printer T,T,TS Parts & Service - Free download as PDF File .pdf), Text File .txt) or read online for free.

LIPI Uploaded. Reference manual.


Matrix printer. T T BACK. QUIT? PRINT. Page 2. Table of contents.

Tally Dot Matrix Printers Model T – CPS

Printer at a glance. 1. Paperways.


3. Installation.

4. Unpacking .

Related Drivers